
تعداد نشریات | 43 |
تعداد شمارهها | 1,685 |
تعداد مقالات | 13,837 |
تعداد مشاهده مقاله | 32,738,551 |
تعداد دریافت فایل اصل مقاله | 12,941,335 |
CFD Simulation of a Wetted-Wall Column for Natural Gas Sweetening Using DEA Solution | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Gas Processing Journal | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
مقاله 3، دوره 5، شماره 2، اسفند 2017، صفحه 13-32 اصل مقاله (1.38 M) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
نوع مقاله: Research Article | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
شناسه دیجیتال (DOI): 10.22108/gpj.2018.108384.1019 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
نویسندگان | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Samaneh Bayati1؛ Ali Mohebbi* 2 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1Department of Chemical Engineering, Faculty of Engineering, Shahid Bahonar University of Kerman, Kerman, Iran | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2Shahid Bahonar university of Kerman | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
چکیده | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Natural gas usually contains significant amounts of acid gases when it is extracted from underground reservoirs. Therefore, it must be treated by appropriate processes to remove these acidic components. In this study, the simultaneous absorption of carbon dioxide and hydrogen sulfide from natural gas into diethanol amine solution was simulated using CFD. Absorption process was performed in a wetted-wall column with counter-current gas-liquid flow. A two-dimensional simulation based on the volume of fluid model was used. To investigate the hydrodynamics of the flow in the column, distribution of the volume fraction of phases along the column, the formation of liquid film and velocity profiles were studied. To validate the results for predicting the liquid film thickness, the column was simulated at different flow rates of water and air in laminar flow regime. Simulation results for liquid film thickness were compared with experimental data. Then by considering the mass transfer from the gas phase to liquid phase based on Higbie’s penetration theory, the concentration distribution of components in gas and liquid phases was calculated. The effect of temperature on absorption of and was also studied. The comparison of simulation results with the experimental data for the outlet concentrations in the gas phase showed that there was a good agreement between them. The developed model can also be used in further studies to determine the effective parameters on simultaneous absorption of and in a wetted-wall column. This helps to optimize the performance of the sweetening process in gas refineries. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
کلیدواژهها | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Natural gas sweetening؛ Carbon dioxide؛ Hydrogen sulfide؛ CFD؛ DEA | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
اصل مقاله | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1. Introduction Natural gas is the most important and the most common fossil fuels in the current age and future. In the world today, natural gas is widely used in household, industries and transportation. Since natural gas is located in deep underground reservoirs, it may contain several non-hydrocarbon components such as carbon dioxide and hydrogen sulfide so it is called sour gas. Gas sweetening is the separation of acid gases from sour gas. Acid gases in the sour gas are undesirable compounds, which cause several problems such as corrosion and environmental pollutions without any thermal value. Therefore, before using natural gas, acid gases should be removed by sweetening processes in the treatment units (Abdulrahman & Sebastine, 2013; Rahimpour, Saidi, Baniadam, & Parhoudeh, 2013). Due to the presence of impurities such as acid gases in natural gas and the problems caused by them, separation processes to remove these gases have always been an important issue. The increasing importance and application of natural gas as an energy source lead to challenges related to the design of separation and purification processes. The utilization of natural gas extracted from natural resources is limited because of high corrosion and environmental problems caused by acid gases. Gas sweetening is usually done in tray towers, packed towers, venturi and spray scrubbers, bubble columns and wetted wall columns (Baniadam, Fathikalajahi, & Rahimpour, 2009; Keshavarz, Fathikalajahi, & Ayatollahi, 2008). Wetted wall columns are important equipment in separation processes and are widely used in theoretical studies of mass transfer because of their simple structure, the specified interface of the two phases and possibility of controlling the process. Among different methods for removing and , chemical absorption using alkanolamine solutions have great applications. Alkanolamines are widely used for acidic components removal from natural gas (Baniadam et al., 2009). Monoethanolamine (MEA), Diethanolamine (DEA), Diisopropanolamine (DIPA) and N-Methyldiethanolamine (MDEA) are the most commonly used amines for removal of and (Mandal & Bandyopadhyay, 2006). MEA and DEA are widely used for simultaneous absorption of and from sour gas and industrial gas streams but MDEA is often used for selective removal of from gas streams containing both and (Mandal & Bandyopadhyay, 2005). Many efforts have been done in the field of natural gas sweetening and finding new ways to increase the efficiency of acid gases removal during the past years. Yih and Sun (1986) worked on simultaneous absorption of and using potassium carbonate and amine-promoted potassium carbonate solutions in a 183 cm long wetted wall column of outside diameter of 2.72 cm. The influences of gas and liquid flow rate, temperature, solvent concentration, promoter type and concentration on absorption rate, mass transfer coefficient and selectivity factor were studied. It was observed that DEA was a more effective promoter for absorption of and . Mandal and Bandyopadhyay (2005) studied the simultaneous absorption of and into aqueous blends of 2-amino-2-methyl-1-propanol (AMP) and diethanolamine (DEA) in their theoretical and experimental investigations. The effects of contact time, amine concentration and temperature on the absorption rate and the selectivity were investigated by absorption experiments in a wetted wall column at atmospheric pressure with a constant feed gas ratio. The diffusion–reaction processes for and mass transfer in blended amines were modelled according to Higbie’s penetration theory with the assumption of reversible reactions. It was observed that the blended amine solvent was an efficient mixture solvent for simultaneous absorption of and and by varying the relative amounts of AMP and DEA, the solvent selectivity for absorption of and can be changed. Mandal and Bandyopadhyay (2006) also studied the simultaneous absorption of and into aqueous blends of DEA and MDEA in their theoretical and experimental investigations. The effect of contact time, temperature and amine concentration on the rate of absorption and the selectivity were investigated by absorption experiments in a wetted wall column at atmospheric pressure and constant feed gas ratio. The diffusion–reaction processes for and mass transfer in blended amines were modelled according to Higbie’s penetration theory with the assumption that all reactions are reversible. Model results based on the kinetics-equilibrium-mass transfer coupled model were found to be in good agreement with the experimental data for absorption rates of and into (MDEA + DEA + H2O). Baniadam et al. (2007) developed a 2D mathematical model for acid gases (i.e. and ) removal in a commercial sieve tray column using MDEA. The velocity profile in the liquid phase in both radial and axial directions was calculated using computational fluid dynamics. Mass and energy equations also were derived and numerically solved in order to define the concentration and temperature profiles in radial and axial directions. The model was based on two film theory. Xu, Paschke, Repke, Yuan, & Wozny (2009) studied the mechanism of absorption and momentum transfer in a laminar, counter current gas and liquid film flow on a plate in a three-dimensional model using computational fluid dynamics. The volume of fluid (VOF) model was used to investigate the hydrodynamics and mass transfer between gas and liquid phases based on penetration theory. Experiments and simulations were done for a system of propane and toluene. The irregular surface of the liquid film, velocity profiles in gas and liquid phases, concentration profiles and output concentrations were studied. There was a good agreement between simulation results and experimental data. Rezakazemi et al. (2010) studied the chemical absorption of and in a hollow fibre membrane contactor (HFMC) theoretically and experimentally. A 2D mathematical model was developed for simultaneous absorption of and in a HFMC using MDEA solution. The radial and axial diffusion were considered in that model. The effects of convection and chemical reactions were also considered in both the shell and tube. Computational fluid dynamics (CFD) was used to solve the equations of continuity and momentum. The experimental data confirmed the model predictions and good agreement was observed between simulation results and experimental data for different values of gas and liquid velocity. The simulation results showed that removal using MDEA solution was very high and was almost completely removed. Their results showed that the membrane used for removal of small amounts of was very effective in high gas to liquid ratios. The model was able to predict the absorption performance of and in the HFMC. In order to screen different amine solvents for capture, Chen, Closmann, and Rochelle (2011) used a wetted-wall column to measure equilibrium partial pressure and absorption/ desorption rates at various loading from 40 to 100 . The heat of absorption, capacity and liquid film mass transfer coefficients were also determined in this study. The results showed that primary amines used in this research (DGA, MAPA and MEA) had low capacity, low absorption rates and high heat of absorption. AMP had a high capacity but suffered from low absorption rate. MDEA blended with PZ showed high capacity and absorption rate with a lower heat of absorption in comparison to primary amines. Rahimpur et al. (2013) developed a mathematical model based on computational fluid dynamics for absorption of acid gases into amine solution in a structured packing with corrugated sheets. 2D mass and energy equations with chemical reactions between acid gases and amine solution were derived for cylindrical coordinate since corrugated plates placed in a way that channels were created along the bed. The temperature and concentration profiles were obtained over the bed in the gas and liquid by solving the governing equations based on mass and energy conservation equations. Rodriguez-Flores, Mello, Salvagnini, and de Paiva (2013) studied absorption into MEA, AMP and their respective blend to evaluate the absorption process and determine a design parameter for a single-amine absorption system. A wetted- wall column with a film promoter, a thin stainless steel woven, was used for experimental tests which were carried out in counter-current flow at 298 K, atmospheric pressure, a constant gas load (10% ) and three different liquid loads. It was concluded that the interfacial area was influenced by increasing the liquid load which means an increase in the effective interfacial area between liquid and gas phase. The values of a related to MEA and the blend based on it were higher in comparison to AMP and the results showed that a value for MEA: AMP mixtures increased by increasing the MEA proportion in the blend. Hosseini, Alizadeh, Fatehifar, and Alizadehdakhel (2014) studied the chemical absorption of into the monoethanolamine solution in a wetted wire column consisting of one wire. The two-phase flow, mass transfer and chemical reaction were simulated using computational fluid dynamics method with applying volume of fluid model. The simulation results were in good agreement with experimental data. Their simulation results showed that by increasing the gas and liquid flow rates, the diameter and intervals of liquid beads increased. The beads velocity also increased by increasing the liquid flow rate and decreasing the mass fraction of MEA in the liquid phase and mass transfer resistance in the liquid phase reduced by formation of the beads. Finally, they concluded that their model was able to predict the effect of physical and operating parameters on the investigated chemical absorption process. Taheri, Mohebbi, Hashemipour, and Rashidi (2016) employed a wetted-wall column to study the simultaneous removal of and from natural gas using a nanofluid containing and nanoparticles and nanoporous graphene in Diethanolamine. The effects of concentration and particle types on absorption of and were studied. The experiments were done at 298 K and with two different inlet gas compositions. The results showed that -DEA nanofluid had deteriorating effects on removal while -DEA improved absorption. It was also observed that absorption rate was enhanced with both –DEA and -DEA nanofluids but was found to be a more effective candidate for absorption. It was also found that the presence of naoporous graphene in DEA solution had a significant effect on absorption of and in comparison to DEA. Karlsson and Svensson (2017) investigated absorption rate using a wetted- wall column with two different solvents, MEA and mixture of AMP in the NMP. Experiments were carried out for various concentrations of amine solutions and the results showed a higher flux and higher liquid side mass transfer of for the mixture of AMP in NMP compared to aqueous MEA. Lillia, Bonalumi, Fosbøl, Thomsen, and Valenti (2018) studied the absorption of into using a wetted- wall column in order to investigate the effect of solvent condition on the rate of reaction. The experimental tests were done at different temperatures, various concentrations and different loadings. They presented the raw data and also the final value of the overall mass transfer coefficient as a result of the raw data treatment. Wang, Xu, Lai, and Sun (2018) developed a multiphase computational fluid dynamics (CFD) model in order to determine the mass transfer coefficient in solvent-based capture using a wetted- wall column. A volume of fluid model was used to model the hydrodynamics and the diffusive and reactive mass transfer between the two phases was modelled by applying a one-fluid formulation. The results for the mass transfer coefficients were compared with the standard two-film theory (STFT). The aim of this study was the simulation of a counter-current wetted-wall column for simultaneous removal of and from natural gas using computational fluid dynamics. The solvent of absorption process was DEA. A 2D simulation based on the volume of fluid (VOF) model was developed. After studying the hydrodynamics of the column, mole fractions of and were calculated in the gas output considering mass transfer from the gas phase to the liquid phase (i.e. absorption of acid gases into the amine solution) and simulation results were compared with the experimental data. 2. Simulation Procedure 2.1. Geometry The structure of the wetted wall column used in this simulation is based on the experimental set up in the Sarkhoon and Qeshm gas Refinery Company for and removal from natural gas. The wetted wall column is made up of two concentric tubes. The inner one is 8 cm long stainless steel wetted- wall tube with an outer diameter of 0.635 cm and thickness of 0.1 cm. The outer tube is 8.5 cm long pyrex tube with an inner diameter of 2.54 cm. Due to the symmetrical geometry of the column, a two-dimensional axisymmetric model was selected for simulation of the two-phase flow in the column. Dimensions of the column are shown in Figure 1.
Figure.1. Dimensions of the wetted-wall column
2.2. Governing Equations 2.2.1. Conservation Equations Conservation equations are used for obtaining the main equations of the laminar fluid flow. For all kind of flows, FLUENT solves the conservation equations of mass and momentum. By writing the mass and momentum balances around a small element of fluid, Navier-Stokes and continuity equations are derived. The velocity and pressure distribution of the fluid are obtained from solving these equations (Fluent 6.3.26 users guide, 2006; Hosseini, 2013). The general form of the continuity equation is shown in Eq. (1) (Fluent 6.3.26 users guide, 2006):
where and are density and the velocity vector respectively. The conservation equation of momentum in the inertial coordinate system is as follows (Fluent 6.3.26 users guide, 2006):
Here is the static pressure, is the stress tensor, and are the gravitational and external body forces respectively. By substituting the equation of stress tensor in Eq. (2), the momentum equation is derived as follows (Fluent 6.3.26 users guide, 2006):
2.2.2. Volume Fraction Equations In a two- phase flow in which the two fluids are immiscible, VOF model is used to track the interface betweenthe two phases. In this model, the volume fraction of each phase is defined as a variable (Hosseini et al., 2014). The total volume fraction of phases is one in each control volume. The equation of volume fraction for liquid phase is shown in Eq. (4) (Ho et al., 2011).
This equation is derived from the conservation of mass in the liquid phase. Since the sum of volume fraction of phases is equal to 1, the gas volume fraction ( ) is calculated from Eq. (5) (Ho et al., 2011).
The volume averaged density and viscosity are estimated using the following equations (Ho et al., 2011).
In Fluent software, the effect of surface tension along the interface of phases is considered by using the continuum surface force (CSF) model. In this model, by applying the surface tension to the VOF calculations, a source term appears in the momentum equation. The source term is as follows (Hosseini et al., 2014):
where K is the interface curvature and is computed from the gradients of the unit normal at the interface (Hosseini, 2013; Hosseini et al., 2014).
here is as follows:
In Fluent, the effect of contact angel between the wall and the fluid is applied by a boundary condition. Near the wall, the contact angle is defined as a measure of adhesion. This boundary condition is applied to the cells near the wall and adjusts the curvature of the interface in these cells. is the contact angel between the fluid and the wall, so the surface normal vector in the cell next to the wall is calculated from Eq. (11).
where and are the unit normal and tangent vectors to the wall (Ho et al., 2011). So, the defined surface curvature for cells is used for the surface tension calculations (Chen et al., 2011). 2.2.3. Mass Transfer The fluid flow in the wetted wall column for simultaneous absorption of carbon dioxide and hydrogen sulfide is along with mass transfer between two phases and also chemical reaction. Species transport equation is derived by solving the conservation equation of chemical species in the multiphase flows. The equation of species transport is as follows (Fluent 6.3.26 users guide, 2006):
where is the volume fraction of phase q, is the mass fraction of component i in the phase q, is the vector of mass transfer flux for component i in the phase q, is the production rate of component i by chemical reaction in the phase q and is the mass transfer rate between components i and j from phase q to the phase p. 2.2.4. Mass Transfer Equation at the Interface Mass transfer rate at the gas-liquid interface is calculated from the equation based on the two-film theory (Hosseini et al., 2014).
where and are the mole fraction of component n at the interface of liquid and gas phases, and are the mole fraction of component n in the bulk liquid and gas phases, is the specific area, is the molecular weight of component n, C is the total concentration of each phase, and are the mass transfer coefficients in liquid phase and gas phase respectively and E is the enhancement factor for considering the effect of chemical reaction. Using the two- film theory and the assumption of equilibrium at the gas- liquid interface, the relationship between and is obtained by Henry’s law.
in the equation (14), the unit of Henry’s constant is . Using the penetration theory, mass transfer coefficients in gas and liquid phases are calculated as follows (Hosseini, 2013):
The contact time at the interface of the two phases is the same and is calculated as follows (Hosseini, 2013):
where is the length of each cell along the flow for numerical simulation and is the interface velocity along the flow. Because of chemical reaction between and amines, the molecular diffusion coefficient of cannot be measured directly. So, the analogy can be used to estimate the diffusion coefficient of carbon dioxide into amine solutions. Based on this analogy, due to the similarities between and olecular structures, diffusion coefficient of into amine solutions is proportional to the diffusion coefficient of into amine solutions. This analogy is shown by Eq. (18).
Where and are the diffusion coefficients of and into water and are calculated as follows:
and Eq. (21) is used to calculate the diffusion coefficient of into DEA solution (Ko, Tsai, Lin, Wang, & Li, 2001).
where is the concentration of DEA solution in terms of . The diffusion coefficient of into amine solution is calculated by the modified equation of Stokes- Einstein as follows (Hosseini, 2013):
where is the viscosity of water and is the diffusion coefficient of into water at . The analogy is also used to determine Henry’s constant of for absorption of it into DEA solution. The Eq. (23) shows this analogy (Penttilä, Dell’Era, Uusi-Kyyny, & Alopaeus, 2011).
The Henry’s constants for dissolution of and in water are defined as follows (Penttilä et al., 2011):
The Henry’s constant for dissolution of into pure DEA is calculated by the Eq. (26) (Penttilä et al., 2011).
Equation (27) is used to calculate Henry’s constant for dissolution of in DEA solution (Penttilä et al., 2011).
here is the mole fraction of component i in the solvent. 1 refers to the water and 2 refers to the DEA. In the above equations, the Henry’s constant is in terms of and temperature is in term of K. The Henry’s constant for dissolution of in water is calculated from the following equation (Carey, Hermes, & Rochelle, 1991):
where is in terms of . When two gases are simultaneously absorbed in a solution containing a component which can react with both of the gases, the absorption rate of each gas would be affected by the other one. The reaction of with primary and secondary amines can be considered as an instantaneous reaction. An instantaneous reaction is limited by diffusion. Since the reaction is very fast, the reactant and the absorbed gas in the liquid phase cannot simultaneously exist in the same area of the liquid. The reaction of with primary and secondary amines is very slower than the reaction of and often can be considered the second order. In this research, the simultaneous absorption of two gases into the liquid containing a component that reacts with both of the gases is simulated based on Higbie’s penetration theory. The reaction of with DEA is instantaneous and the reaction of with DEA is considered second order (Haimour & Sandall, 1983). Because of chemical reaction in the liquid phase, in Eq. (12) should be substituted with the kinetics of reaction. Equation (29) gives the mechanism of reaction between and DEA. Since this reaction is so fast, it can be considered as an instantaneous reaction. The mechanism of reaction between and DEA is also given by Eq. (30) (Versteeg, Van Dijck, Van Swaaij, 1996).
here is DEA and . Equation (31) shows the rate of the reaction between and DEA using the reaction constant developed by Blanc and Demarais (Versteeg et al., 1981).
in which T is in term of K and concentrations are in terms of . 2.3. Solution Method Due to the dynamic nature of the two-phase flow, unsteady state calculations were chosen for the solution of the equations with a time step of s and the residual amount of the parameters was considered 0.001. The SIMPLE algorithm was used for pressure-velocity coupling calculations. The PRESTO! method was selected for discretizationof the pressure equation and a second order upwind calculation method was applied for discretization of momentum, volume fraction and species equations. The equations of mass transfer rate between two phases were defined using the user-defined function (UDF). 2.3.1. Initial and Boundary Conditions Uniform velocity inlet and atmospheric pressure outlet were used as boundary conditions for inlet and outlet of the phases respectively. At the walls of the column, no-slip boundary condition was applied. At time zero, gas and liquid velocity magnitudes and volume fraction of liquid phase were set to zero as initial conditions. Table 1 shows the compositions, volume flow rates and inlet velocities for both gas and liquid phases.
Table.1.Compositions, volume flow rates and inlet velocities for gas and liquid phases
3. Results and Discussion In this section, the results of CFD simulation for VOF profile and liquid film formation with time, pressure, velocity and concentration profiles are presented. Simulation results for mole fractions of and in output gas are compared with experimental data. Then the concentration distribution in gas and liquid phases and the effect of temperature on absorption process are investigated. Figure 2 shows the geometry generated in Gambit software for liquid film formation. After the complete formation of the liquid film, since the effective length for absorption process is x=0 to x=8 cm, the geometry shown in Figure 3 was used for mass transfer simulation.
Figure.2. The generated geometry in Gambit software for simulation of liquid film formation
Figure.3. The generated geometry in Gambit software for simulation of mass transfer process In order to reduce the calculations time and also less precision required in the gas phase, smaller and larger grid sizes were used for liquid and gas regions respectively. The grid independency was checked by using three different mesh sizes with a total number of 116850, 121000 and 142750 cells. The results of these three cases were close together for the average thickness of the liquid film. Therefore the grid with 121000 numbers of cells was selected as the suitable grid. 3.1. Validation of Simulation Results for Liquid Film Thickness In order to validate the simulation results for liquid film thickness, as respects the liquid film thickness for 10% DEA solution has not been measured experimentally, the column is simulated for different flow rates of water-air flows in laminar flow regime. The results of these simulations for the film thickness are compared with the experimental data published by Yih and Hsu (1985) and also Zhou, Gambaryan-Roisman, and Stephan (2009) in laminar flow regime. Table 2 gives the results of these comparisons. As it is observed, by increasing the Reynolds number, the average film thickness increases and there is a good agreement between simulation results and the experimental data. So it is concluded that the developed model can determine the liquid film thickness in laminar flow regime and does not need to guess an initial value for film thickness unlike similar works previously done. 3.2. VOF Profile To determine the volume fraction of each phase, VOF equation with mass conservation (continuity) and conservation of momentum (Navier-Stokes) equations were solved. Figure 4 shows the formation of the liquid film with time. In this figure, red colour refers to the presence of DEA solution and the dark blue refers to the presence of natural gas ( +C + S). As it can be seen, after the liquid overflows, a thin film streams down on the wall and finally exits the column. It takes about 48 seconds to form a stable liquid film.
Table.2. Comparison of simulation results and experimental data for liquid film thickness in two different Reynolds numbers of liquid
Figure.4. Contours of liquid volume fraction for aqueous DEA solution (10-wt% DEA) with the passage of time
Figure.5. Contour of velocity magnitude for counter current gas-liquid flow in the wetted-wall column
3.3. Velocity Profile Obtaining the correct distribution of velocity is very important in order to simulate the counter current gas-liquid flow in the column. The simulation results for velocity magnitudes are shown in Figsure 5 and 6. As one can see, the velocity magnitude is zero on the wall due to applying a no-slip condition on this wall. The profile of velocity magnitude at x= 4 cm is clearly shown in Figure 6. As can be seen, the velocity magnitude is zero on the walls (r= 0.3175 cm and r= 1.27 cm) due to the no-slip condition. Because of the counter current gas-liquid flow, the mixture velocity tends to zero at r=0.64 cm. Figure 7 shows the axial velocity contour so that the negative values refer to the liquid film flow in the opposite direction of gas flow. The profile of axial velocity at x= 4 cm is shown in Figure 8. The gas-liquid counter current flow is clearly shown by negative values for downward liquid flow and positive values for upward gas flow in the column.
Figure.6. Profile of velocity magnitude (m/s) at x=4 cm
Figure.7. Axial velocity contour for counter current gas-liquid flow in the wetted-wall column
In Figure 9 axial velocity profiles in different heights of the column are compared together. As can be seen, the velocity profiles are completely coincident so that both liquid and gas flow in the column can be considered fully developed after x= 2 cm.
Figure.8. Profile of axial velocity (m/s) at x=4 cm
Figure.9. Comparison of axial velocity profiles in different heights of the column
In Figure 10 the counter-current flow of gas and liquid is clearly shown by using the vector form of axial velocity. As can be seen the liquid moves downward and the gas flow direction is upward. 3.4. Validation of the Simulation Results In order to validate the applied model, simulation results for outlet concentrations of acid gases were compared with experimental data obtained in Sarkhoon and Qeshm gas refinery laboratory at 25, 30 and 35 . Tables 3 and 4 show a good agreement between the simulation results and the experimental data. As the simulation results show, and output mole fractions increased as the temperature increased. When the temperature increased from 25 to 30 , output mole fraction rose from 0.00701 to 0.00736 which is 4.99 % increase and output mole fraction increased from 6.04 ppm to 6.61 ppm which showed a rise of 9.44 %. At 35 and output mole fractions increased 0.68 % and 11.8 % respectively toward 30 . So, it can be concluded that was more sensitive to temperature changes.
Figure.10. Vector form of the axial velocity (m/s) for counter current gas-liquid flow Table.3. Comparison of simulation results and experimental data for mole fraction in the column gas outlet
Table.4. Comparison of simulation results and experimental data for mole fraction in the column gas outlet
For obtaining the concentration distribution in the column, the species transport equations were solved with other equations simultaneously. The UDF was also applied for considering the mass transfer between two phases. Mole fraction changes for and in the gas phase are shown in Figurs. 11 and 12 respectively. As expected, with the upward flow of the gas, the acid component mole fractions are decreased and in the upper part of the column due to the gas contact with fresh amine, more changes are observed for and concentrations. As the solvent goes downward, the amount of absorbed acid gases is increased. Thus, fewer changes are observed in the acid gas concentrations in the lower part of the column.
Figure.11. Contour of mole fraction in the gas phase
Figure.12. Contour of mole fraction in the gas phase
Figure 13 shows the changes of mole fraction in radial direction at three different sections , and . As one can see, the mole fraction of in the bulk gas is more than the gas interface and at the liquid interface is more than the mole fraction in the bulk liquid. In the upper sections of the column, more concentration changes are observed in the gas phase due to the gas contact with fresh amine solution. Figure 14 compares the changes of radial concentration profiles in the gas phase at different sections of the column. As it is shown, in the lower part of the column where the gas has just entered the column (x=2 cm), concentration in the gas is high but with upward flow and absorption of in the solvent, concentration in the gas phase decreases in the upper part of the column (x=7 cm).
(a)
(b)
(c) Figure.13. mole fraction profiles at three different sections of the column (a) x=2cm (b) x=5cm (c) x=7cm
Figure.14. Comparison of mole fraction profiles in the gas phase at different sections of the column
Figures 15 and 16 also show concentration profiles. The changes of mole fraction in both gas and liquid phases at different heights of the column are shown in Figure 15. As it is shown in Figure 16, the mole fraction of in the gas phase decreases with upward flow and absorption of in the solvent. Figure 16 shows the changes of concentration profiles in the gas phase at different heights clearly. As the gas flows upward through the column, is absorbed in the amine solution, so more changes are observed in concentration in the gas phase at upper parts of the column.
(a)
(b)
(c) Figure.15. mole fraction profiles at three different sections of the column (a) x=2cm (b) x=5cm (c) x=7cm
Figure.16. Comparison of mole fraction profiles in the gas phase at different sections of the column
When is transferred from the gas to the liquid phase, it reacts with DEA in the solution and is consumed. Figure 17 shows the reaction rate in the liquid phase. As can be seen, in the liquid phase is consumed according to a second-order reaction at the liquid interface and the reaction only occurs at the interface. In a gas absorption process using a wetted wall column, the fresh solvent enters from the top of the column (x=8 cm). and mole fractions in the solvent increase in the flow direction with downward flow and absorption of acid gases in the solvent. Also, due to the reaction between and DEA in the liquid phase, the mole fraction of reaction products increase as the liquid moves downward. Figure 18 shows the changes of and mole fractions and Figure 19 shows the changes of reaction products mole fractions in the liquid phase.
Figure.17. Reaction rate of in the liquid phase in terms of (kgmol/ )
(a)
(b) Figure.18. Changes in acid gases mole fractions in the solvent (a) (b)
(a)
(b) Figure.19. Changes of reaction products mole fractions in the solvent (a) (b)
(a)
(b) Figure.20. Changes in acid gases mole fractions in the gas phase (a) (b)
The sour gas enters from the bottom of the column (x=0) and as it flows upward, acid components are absorbed in the solvent so that the output gas contains less and . Figure 20 shows the changes of and mole fractions in the gas phase.
3.5. The Effect of Temperature on the Absorption of Acid Gases In order to evaluate the effect of temperature on the absorption of and , the process was simulated at 25, 30 and 35 . The results of and mole fractions in the output gas are shown in Table 5. As can be seen, the mole fraction of acid gases increased with increasing temperature, which means the absorption amount is decreased as the temperature increased and this is completely explainable due to the exothermic absorption reaction.
Table.5. The effect of temperature on absorption of and in the solvent
4. Conclusions The simultaneous absorption of carbon dioxide and hydrogen sulfide from natural gas into DEA solution in a wetted wall column was simulated using computational fluid dynamics (CFD). The volume of fluid (VOF) model was applied for simulating the gas-liquid two-phase flow. In order to study the hydrodynamics of the process, volume fraction distribution of the phases, liquid film formation and its thickness and velocity profiles were investigated and it was observed that the developed model was applicable to predict the liquid film thickness carefully in a wetted wall column and in comparison with previous works there is no need to determine an initial value for liquid film thickness. Then by considering mass transfer from the gas phase to the liquid phase, absorption of and into the solvent was simulated and concentration distribution of the components in the column was obtained. In order to study the effect of temperature on absorption of and , the absorption process was simulated at 25, 30 and 35 . It was observed that by increasing temperature, the absorption of acid gases was decreased. The simulation results were compared with the experimental data for output concentration of acid components in the gas and a good agreement was observed between them. In conclusion, the effects of different parameters on absorption process can be studied using these numerical simulations without the need for costly research experiments. Acknowledgments The authors acknowledge Sarkhoon & Qeshm gas treating company for providing us with the experimental data. Note: This research did not receive any specific grant from funding agencies in the public, commercial, or not-for-profit sectors.
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
مراجع | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Abdulrahman, R. K., & Sebastine, I. M. (2013). Natural gas sweetening process simulation and optimization: A case study of Khurmala field in Iraqi Kurdistan region. Journal of Natural Gas Science and Engineering,14,116-120.
Baniadam, M., Fathikalajahi, J., & Rahimpour, M. R. (2009). Incorporation of Eulerian–Eulerian CFD framework in mathematical modeling of chemical absorption of acid gases into methyl diethanol amine on sieve trays. Chemical Engineering Journal, 151, 286-294.
Carey, T. R., Hermes, J. E., & Rochelle, G. T. (1991). A model of acid gas absorption/ stripping using methyldiethanolamine with added acid. Gas Separation & Purification, 5.
Chen, x., Closmann, F., & Rochelle, G. T. (2011). Accurate screening of amines by the Wetted Wall Column. Energy Procedia, 4, 101–108.
Fluent 6.3.26 users guide, fluent, Inc., (2006).
Haimour, N., & Sandall, O. C. (1983). Selective removal of hydrogen sulfide from gases containing hydrogen sulfide and carbon dioxide using diethanolamine. Separation Science and Technology, 18, 1221-1249.
Ho, C. D., Chang, H. C., Chen, H. J., Chang, C. L., Li, H. H., & Chang, Y. Y. (2011). CFD simulation of the two-phase flow for a falling film microreactor. International Journal of Heat and Mass Transfer, 54, 3740-3748.
Hosseini, S. M., Alizadeh, R., Fatehifar, E., & Alizadehdakhel, A. (2014). Simulation of gas absorption into string-of-beads liquid flow with chemical reaction. Heat Mass Transfer, 50, 1393-1403.
Hosseini, S. M. (2013). Simulation of fluid flow hydrodynamics in a wetted- wire column, M. Sc. Thesis, Sahand University of Technology, Tabriz, Iran.
Karlsson, H., & Svensson, H. (2017). Rate of absorption for absorption systems using a wetted wall column. Energy Procedia, 114, 2009 – 2023.
Keshavarz, P., Fathikalajahi, J., & Ayatollahi, S. (2008). Mathematical modeling of the simultaneous absorption of carbon dioxide and hydrogen sulfide in a hollow fiber membrane contactor. Separation and Purification Technology, 63, 145-155.
Ko, J. J., Tsai, T. C., Lin, C. Y., Wang, H. M., & Li, M. H. (2001). Diffusivity of nitrous oxide in aqueous alkanolamine solutions. J. Chem. Eng. Data, 46, 160-165.
Lillia, S., Bonalumi, D., Fosbøl, P. L., Thomsen, K., & Valenti, G. (2018). Experimental data of the aqueous and absorption at temperatures from 15 °C to 35°C, concentrations from 5% to 15% and loadings from 0.2 to 0.6 measured with the Wetted Wall Column. Datain Brief, 17, 1240– 1244.
Mandal, B. P., & Bandyopadhyay, S. S. (2005). Simultaneous absorption of carbon dioxide and hydrogen sulfide into aqueous blends of 2-amino-2-methyl-1-propanol and diethanolamine. Chemical Engineering Science, 60, 6438-6451.
Mandal, B. P., & Bandyopadhyay, S. S. (2006). Simultaneous absorption of and into aqueous blends of N-methyldiethanolamine and diethanolamine. Environ. Sci. Technol.,40, 6076-6084.
Penttilä, A., Dell’Era, C., Uusi-Kyyny, P., & Alopaeus, V. (2011). The Henry’s law constant of and in aqueous binary and ternary amine solutions (MEA, DEA, DIPA, MDEA, and AMP). Fluid Phase Equilibria, 311, 59-66.
Rahimpour, M., Saidi, M., Baniadam, M., & Parhoudeh, M. (2013). Investigation of natural gas sweetening process in corrugated packed bed column using computational fluid dynamics (CFD) model. Journal of Natural Gas Science and Engineering, 15, 127-137.
Rezakazemi, M., Niazi, Z., Mirfendereski, M., Shirazian, S., Mohammadi, T., & Pak, A. (2011). CFD simulation of natural gas sweetening in a gas–liquid hollow-fiber membrane contactor. Chemical Engineering Journal, 168, 1217-1226.
Rodriguez-Flores, H. A., Mello, L. C., Salvagnini, W. M., & de Paiva, J. L. (2013). Absorption of into aqueous solutions of MEA and AMP in a wetted wall column with film promoter. Chemical Engineering and Processing, 73, 1– 6.
Taheri, M., Mohebbi, A., Hashemipour, H., & Rashidi, A. M. (2016).Prepration of graphene-amine nanofluid for absorption of carbon dioxide ( ) and hydrogen sulfide ( ) from in a wetted wall column. Gas Processing Journal,4(1), 29-41.
Taheri, M., Mohebbi, A., Hashemipour, H., & Rashidi, A. M. (2016). Simultaneous absorption of carbon dioxide ( ) and hydrogen sulfide ( ) from - - gas mixture using amine-based nanofluids in a wetted wall column. Journal of Natural Gas Science and Engineering, 28,410- 417.
Versteeg, G. F., Van Dijck, L. A. J., & Van Swaaij, W. P. M. (1996). On the kinetics between CO2 and alkanolamines both in aqueous and non-aqueous solutions. and overview. Chem. Eng. Comm., 144, 113-158.
Wang, C., Xu, Z., Lai, C., & Sun, X. (2018). Beyond the Standard Two-Film Theory: Computational Fluid Dynamics Simulations for Carbon Dioxide Capture in a Wetted Wall Column. Chemical EngineeringScience, 184, 103-110.
Xu, Y. Y., Paschke, S., Repke, J. U., Yuan, J. Q., & Wozny, G. (2009). Computational approach to characterize the mass transfer between counter-current gas-liquid flow. Chem. Eng. Technol., 32, 1227-1235.
Yih, S. M., & Hsu, T. Y. (1985). Gas absorption into wavy and turbulent non-Newtonian falling liquid films in a wetted-wall column. Chemical Engineering Communication, 34, 65-76.
Yih, S. M., & Sun, C. C. (1987). Simultaneous absorption of hydrogen sulphide and carbon dioxide into potassium carbonate solution with or without amine promoters. The Chemical Engineering Journal, 34, 65-72.
Zhou, D. W., Gambaryan-Roisman, T., & Stephan, P. (2009). Measurement of water falling film thickness to flat plate using confocal chromatic sensoring technique. Experimental Thermal and Fluid Science, 33, 273–283. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
آمار تعداد مشاهده مقاله: 1,210 تعداد دریافت فایل اصل مقاله: 506 |